ZUKIWORLD Online | Suzuki 4x4 Editorial and Forum
ZUKIWORLD Discussion Forum => Suzuki 4x4 Forum => Topic started by: arkangel on March 30, 2006, 08:47:49 AM
-
Hi All,
I think this question has been done before but I'm not as good in english to search effectively in the search engine :(
My Vitara is a 98, 2 doors, 5 Speed Manual tranny, Stock "everything" in the drivetrain, Just added a set of coil spacers (1.5" on front and 2" on back)
Actually I'm using 235/75 BF AllTerrains and they are almost flat. I'm saving some money for a new set of rubbers.
What's the maximum size of tires I can put on my truck?
I'm thinking about 30x9.5 OR 31x10.5 ::) but I don't want to loss some "horses" in power just to have 31's.....
Comments? I need the experience of you guys ;D
-
Welcome aboard arkangel
I think that a 30"inch tire will get you what you want.
Just a hair power lost but not too bad (my daily driver has 32"s)
swapping out to 30-31"s on my daily driver is on my mind
(if I find a cheap good set used)
-
i have a 1.5 inch lift and run 30x9.5's, they rub on the frame only at full turn. there is some power loss and i have the 2.0 4cyl, nothing to be worried about though.
-
How about some more photos of that front bumper? Is the rear also custom?
-
I'll try to post some pics of both bumpers ;D
But I need some minutes to resize 'em to fit in here..
-
Here some pics of the bumpers I designed 8)
These are during the 1st day, justspot welding the tubing ;D
-
These were taken after paint was "touch resistant" ;)
Hellas weren't even connected :-[
BTW, these Hellas are gone :'( someone wanted them more than me and "took 'em away" without persmission >:(
-
I REALLY like the bumpers!! YES!
-
Whole damned truck looks pretty sharp.
-
Hey Hey guys, you are overreacting ....... ;D
and you've not seen the inside yet ::)
My future plans are the 30x9.5 Muds, complete the instalation of the VHF/UHF second antenna setup, 800 MHz CDMA antenna, intall the wiring for brighter lights and design a mount system for my 60" Hi Lift jack, maybe on the roof rack.
-
Luis, those bumpers are muy bueno! I think I may copy those if I can get my hands on a bender! ;D
-
OK, if you need more detailed pics just let me know.
I'm planning to weld some sort of "protection" on front soon :D
-
I have 1 1/4 in front and 1 3/4 in rear and i fit 31 no prob. you have to give the inner fender some inspiration with a hammer but nothin too bad. if im haulin booty in the driveway it acccasionly rubs. but 99% i have no problems. good lookin bumpers by the way.
lance
-
It made it up right here with open diffs. these little guys are champs. it bounced a but but popped right up. :)
-
Hello,
Nice job on the Bumpers!!!! I like the front one..It kinda looks like mine.
Later Tom K.
-
Nice work, arkangel! I would appreciate if you could provide some more details because I would like to try making some for my 98 Tracker. What did you use to bend the tubes? I just got an oxy/acetylene welding kit and I'm going to try to teach myself how to weld. Do you think I can make those bends with a torch?
Sorry to hear that some jackass decided to part with your Hellas.
-
What did you use to bend the tubes? .............................. Do you think I can make those bends with a torch?
Not pretty bends... not with keeping them accurate.. if you can.. I would be highly impressed..
Get an el-cheap pipe bender from Harbor Freight.. takes a while but makes pretty OK bends..
-
I know that 31" BFGs MTs would fit but I think I'm going to loose more power... So maybe sticking on 235s or going up to 30s would be a smart choice. Man my 1.6 8V is slow now, so I don't want to be "slower" ;D
-
I like bumpers made of tubing 'cause they're NOT heavy. That design looks lighter than mine :o
-
The bender used is similar to that one used to bend exhaust pipes. But uses more PSIs because the wall of these tubes is a lil bit thicker.
I'll take a few more shot and post 'em for you all, ;D
BR,