ZUKIWORLD Online | Suzuki 4x4 Editorial and Forum
ZUKIWORLD Discussion Forum => Classified Ads => Topic started by: tipover on September 02, 2010, 04:42:49 PM
-
Parting out and cleaning out the shop. Parts are in NorCal and prices are OBO plus shipping. Parts are samurai unless specified.
Hood with couple of small dings 100
Windshield frame with good glass 200
targa 25
Complete Stock Roll bar 30
I also have the sheet metal above doors and the bars that tie from widshield and targa OBO
86-88 tack dash comes with dash trim/screws 50
several stock front and rear inner axles. 30 each
Good engine 250 for long block.
Stock rear third welded diff 100
Sidekick rear third 5.125 50
2 large bolt pattern diff flanges from sidekick front 20 ea.
One set of grey plastict stock fender flares paint peeling but straight75
set of 26 spline side gears 50
will add as i find more.
added stock Front Driveline 50
Starter 20
High steer stage I (passanger arm and drag link and hardware) 150
Mercedes arms already machined with all hardware, like new. 45
Jason
-
make offers.
-
One set of grey plastict stock fender flares paint peeling but straight75
how much to ship to 81631?
-
90 shipped?
-
How much for the 5.125 sidekick third shipped to 23936
-
45 for shipping. may be sold, guy coming tomorrow. let ya know.
-
up dated.
-
Hi, I'm interested in the two bars that connect the targa to the windshield, I've been trying to locate a pair to purchase for about a year now. If you still have them will you give me a call at 502 669 2200 or email me at Hoo_tal|removethispart|@hotmail.com. If you still have them I'd like to purchase them immediately.
Thank you,
Joel Hinton
-
I'm also interested in the break backin plates for the sj410
-
I'm also interested in the break backin plates for the sj410
sold
-
Hi, I'm interested in the two bars that connect the targa to the windshield, I've been trying to locate a pair to purchase for about a year now. If you still have them will you give me a call at 502 669 2200 or email me at Hoo_tal|removethispart||removethispart|@hotmail.com. If you still have them I'd like to purchase them immediately.
Thank you,
Joel Hinton
Are you talking about the support above the doors or the two bars from the windshield to the targa that has the padding on it.
-
The two bars that connect the targa to the windshield with padding. I've been looking everywhere forever trying to get a pair.
-
Parting out and cleaning out the shop. Parts are in NorCal and prices are OBO plus shipping. Parts are samurai unless specified.
Hood with couple of small dings 100
Windshield frame with good glass 200
targa 25
Complete Stock Roll bar 30
I also have the sheet metal above doors and the bars that tie from widshield and targa OBO
86-88 tack dash comes with dash trim/screws 50
several stock front and rear inner axles. 30 each
Good engine 250 for long block.
Stock rear third welded diff 100
Sidekick rear third 5.125 50
2 large bolt pattern diff flanges from sidekick front 20 ea.
One set of grey plastict stock fender flares paint peeling but straight75
set of 26 spline side gears 50
will add as i find more.
added stock Front Driveline 50
Starter 20
High steer stage I (passanger arm and drag link and hardware) 150
Mercedes arms already machined with all hardware, like new. 45
Jason
PM sent concerning the Highsteer.... Tux...
-
When i get home sunday, ill send pic. Let me know where to send them.
The two bars that connect the targa to the windshield with padding. I've been looking everywhere forever trying to get a pair.
-
Could you part with the timing belt cover? If its fully intact shipped to 34117.
-
Could you part with the timing belt cover? If its fully intact shipped to 34117.
No i dont have an extra belt cover.
-
interested in the stage one steering parts. would I need any thing else to make this work on my 86 sammy?
-
interested in the stage one steering parts. would I need any thing else to make this work on my 86 sammy?
If its not too high no. I have 2 draglinks. Just tell me which one you want. One is a converted stock tie rod than has a suzi ball on one end for suzuki box and the ball joint on the other that fits the new arm. I think its a toyota. The other link has hiems. It you use that one, you have to drill out the pitman arm and th arm. Take your pick.
-
I never recied a pic of the bars from the targa to the windshield. If you still have them I have the money and our wanting to purchase them immediately. Please contact me by phone or email 502 669 2200 hoo_tal|removethispart|@hotmail.com
-
Emailed the pic...
-
do you have the cylinder head for the 1.3L
-
rather not separate aa good engine...
-
I need the passenger side wiper assembly.