Hello Guest
« previous next »
Pages: [1]   Go Down

Any suggestions for a front end bottoming out issue?

  • 7 Replies
  • 1740 Views

0 Members and 1 Guest are viewing this topic.

*

Offline RJkick

  • 632
  • 5
  • Gender: Male
Any suggestions for a front end bottoming out issue?
« on: November 24, 2009, 11:30:44 AM »
I tried to get some help from Daystar EVS Shock bumpstops but they just slid over the top of the strut and caused a bit of fluid loss and split almost in two after 1 trip.  I don't jump but the front end does get up some times and this is the result.  I have OME springs and struts ala rockmolesters lift, Calmini strut extensions instead of a strut flip, and 31X10.5 tires

Any thoughts
« Last Edit: November 24, 2009, 11:34:51 AM by rjkick »
Logged
92 Sidekick 1.6L 16v Calmini\OME 4.5" lift 3" Body Lift OME962 springs in front w\.75" spacers OME955 in rear w\1.75" spacers Extreme Duty Strut Eliminator kit and rear ProComp MX6 Shocks 31X10.50 Nexen M\T   Thorley Header   2" exhaust  Calmini front truss bar and stabilizer and skids   Custom Bumpers and Rock Rails  Limit Straps
*

Offline Zukipilot

  • 7160
  • 25
  • Gender: Male
  • stretch the limits of reality!!!
Re: Any suggestions for a front end bottoming out issue?
« Reply #1 on: November 24, 2009, 11:40:29 AM »
If I remember correctly the OME springs are a 1.5" lift. If this is the case, the Calmini drop is for a 3" lift and will have the strut mount to low for the lift you are have. The strut upper mount flip is for a 1.5-2" lift and will work better for your set up. (assuming my memory is correct about the OME springs).

Zig
Logged
Zukipilot
'92 Liberty Overland Sidekick
*

Offline Cuthulu

  • 384
  • 0
  • Gender: Male
  • I'd kill for a Nobel Peace Prize.
Re: Any suggestions for a front end bottoming out issue?
« Reply #2 on: November 24, 2009, 06:10:35 PM »
Quote from: Zukipilot on November 24, 2009, 11:40:29 AM
If I remember correctly the OME springs are a 1.5" lift. If this is the case, the Calmini drop is for a 3" lift and will have the strut mount to low for the lift you are have. The strut upper mount flip is for a 1.5-2" lift and will work better for your set up. (assuming my memory is correct about the OME springs).

Zig

You can get 1.5 and 2" from OME but I have never seen anything larger.  Doesn't CrickyMike work for ARB?  If so I bet he could be the definitive answer.

Even if its the 2" with the strut mounts you will be exceeding the spring limit.
« Last Edit: November 25, 2009, 03:06:04 AM by Cuthulu »
Logged
*

Offline BRD HNTR

  • 2300
  • 56
  • Gender: Male
Re: Any suggestions for a front end bottoming out issue?
« Reply #3 on: November 24, 2009, 09:30:22 PM »
It does seem that the Calmini strut extensions are too long for the springs he is running.
Logged
93 Tracker,XL7 springs & 1" raised spring pads in front with YJ springs in back, home built bumpers rear & front (w/winch), 2" x 4" rock tubes,  ARB front & rear, converted Sami rear to IFS, 33x12.5x15  aluminum rims, roll cage, 2.7L w/5 speed auto.
*

Offline RJkick

  • 632
  • 5
  • Gender: Male
Re: Any suggestions for a front end bottoming out issue?
« Reply #4 on: November 25, 2009, 11:48:31 AM »
Rockmolester stated he got about 4 to 4.5 inches of lift.  He did flip the strut mounts but I figured since I had the spacers I would try them.   I'll measure but what are the thoughts of the strut now not having enough down travel when one of the tires gets a little air.  I shouldn't need a limiting strap right?  I do like the fact those $20 EVS foam bumps saved me from busting through the strut mount, which was a previous issue.

Thanks
Logged
92 Sidekick 1.6L 16v Calmini\OME 4.5" lift 3" Body Lift OME962 springs in front w\.75" spacers OME955 in rear w\1.75" spacers Extreme Duty Strut Eliminator kit and rear ProComp MX6 Shocks 31X10.50 Nexen M\T   Thorley Header   2" exhaust  Calmini front truss bar and stabilizer and skids   Custom Bumpers and Rock Rails  Limit Straps
*

Offline Drone637

  • 8121
  • 116
  • Gender: Male
  • Evil Cow
Re: Any suggestions for a front end bottoming out issue?
« Reply #5 on: November 25, 2009, 12:08:58 PM »
Another Zukiworld member put limiting straps on his front suspension with the OME struts.  He found that maxing out the suspension caused the OME struts to self destruct.

Logged
96 Geo Tracker, x-SJ-410,  x-White Rabbit, x-Project Trouble
Crawlers NorthWest
x-Trouble Racing
*

Offline mrfuelish

  • *
  • 2862
  • 13
  • Gender: Male
  • you must have a perception problem.
Re: Any suggestions for a front end bottoming out issue?
« Reply #6 on: November 25, 2009, 12:34:59 PM »
maybe you could put a Bump stop on the lower A arm or inside of the spring? your shock does need more travel that's a given.
Logged
1987,1988,1988,1990 samurai's,  1953 m38a1,  1996 x-90,blue.1996 x-90 red.1994 2 door tracker.   only Dead Fish go with the flow.                No Hairy Nosed Wombats were ran over on the trail today.       My ZUK is Xenophobic.
*

Offline bzzr2

  • 1011
  • 3
Re: Any suggestions for a front end bottoming out issue?
« Reply #7 on: November 26, 2009, 08:04:59 PM »
are there not stock bumpstop extensions on that model inside the spring?  if so you could order some bumpstop extensions from bits4bits..
Logged
03-ZR2, 2dr, 31x10.5 SSR's & stuff...--sold :-(
03 xl7, jeff's 2inch spacer lift, 225/75/16's; sold
09 taco reg cab short box 4x4
Pages: [1]   Go Up
« previous next »