Hello Guest
« previous next »
Pages: [1]   Go Down

sammy case mated to a tracker case?

  • 6 Replies
  • 2475 Views

0 Members and 1 Guest are viewing this topic.

*

Offline 1bigtracker

  • 3409
  • 1
  • Gender: Male
  • F*** trail rated, try trail tested
sammy case mated to a tracker case?
« on: April 04, 2004, 03:47:25 AM »
is their any easy way to do this without sending them to OTT.  my friend has a alum. welder so he can cut the output off my case and weld it up.  i have never seen a sammy case.

stu
Logged
   
*

Offline Wildweasel

  • 106
  • 0
  • Gender: Male
  • Git er Done!
    • Wildweasel's world
Re: sammy case mated to a tracker case?
« Reply #1 on: April 04, 2004, 07:26:24 AM »
Unless you push your rear axle back (6") the rear driveshaft
will be too  short. My outdated web pages have info and some pics on doing this.  
Logged
Glenn
91 geo tracker, Toyota axles, twin tcases,35's too many mods to list.
*

Offline idaholwb

  • 772
  • 2
  • Gender: Male
  • And that's the way the metal crumpled!
Re: sammy case mated to a tracker case?
« Reply #2 on: April 04, 2004, 12:56:47 PM »
 The kicker setup only requires shipment of the kick case. He hasn't gotten around to taking the other part off the website yet. The kicker is about 1 1/2" shorter than stock, minus the extra length you would need for the intermediate driveline and sammy case input flange.....bare minimum of 6"!
Easier to go through OTT, they already have it figured out. And it really isn't that expensive.
Logged
97 Sport
265/70-16s
2" lift
2.0 swap
I know...Pretty boring... FOR NOW...
*

Offline whitfield

  • 633
  • 0
  • Gender: Male
  • 4-dr Kick on 34's
Re: sammy case mated to a tracker case?
« Reply #3 on: April 04, 2004, 05:37:11 PM »
Quote
Unless you push your rear axle back (6") the rear driveshaft
will be too  short. My outdated web pages have info and some pics on doing this.  



But I've got a 4dr... ;D   Gotta look into this.  I have a few sammy cases laying around
Logged
Old Dog looking to learn some new tricks. 

*

Offline Wildweasel

  • 106
  • 0
  • Gender: Male
  • Git er Done!
    • Wildweasel's world
Re: sammy case mated to a tracker case?
« Reply #4 on: April 04, 2004, 10:52:49 PM »
Ott is the way to go for sure, bt he was asking if you can do it without OTT. (I did mine just before they released the ott3 I think) and I didn't have the funds then anyway,
My rear driveshaft is 18 1/4" long. (toy CV type) and the driveline angles arn't bad so there have been no problems with it.
Logged
Glenn
91 geo tracker, Toyota axles, twin tcases,35's too many mods to list.
*

Offline whitfield

  • 633
  • 0
  • Gender: Male
  • 4-dr Kick on 34's
Re: sammy case mated to a tracker case?
« Reply #5 on: April 04, 2004, 11:07:01 PM »
Thanks Wildweasel,   Nice to know that it can be done sucessfully at home in the shop, where things cost much less.  I have been checking out  your web page on the WW3.   Any more updates?


OOOOh   I see!   nice.
« Last Edit: April 04, 2004, 11:15:44 PM by whitfield »
Logged
Old Dog looking to learn some new tricks. 

*

Offline Wildweasel

  • 106
  • 0
  • Gender: Male
  • Git er Done!
    • Wildweasel's world
Re: sammy case mated to a tracker case?
« Reply #6 on: April 05, 2004, 01:13:09 AM »
If I have some time at work this week I am going to try to get some updates on the site, I just have been kind of busy as of late. My site is out of date as to what I have done on the Tracker.  (Now evan more so)
I will post a link to the updates when I get to them.
Logged
Glenn
91 geo tracker, Toyota axles, twin tcases,35's too many mods to list.
Pages: [1]   Go Up
« previous next »