Hello Guest
« previous next »
Pages: [1]   Go Down

Removing the rocker trim support.

  • 6 Replies
  • 3614 Views

0 Members and 1 Guest are viewing this topic.

*

Offline pharoe7

  • 7
  • 0
Removing the rocker trim support.
« on: July 23, 2012, 05:45:56 PM »
Does anyone know the best way to remove the metal support for the plastic molding on the rocker panel below the doors? I've taken the plastic molding off already but the metal support seems to be on there pretty good either glued or welded, I can't tell. Though I don't see any welds. Let me know if anyone has removed it successfully.

Thanks
Logged
*

Offline Merlin93

  • 170
  • 4
  • Gender: Male
Re: Removing the rocker trim support.
« Reply #1 on: July 23, 2012, 08:48:12 PM »
Your answer might be contained here:
http://zukiworld.com/month_110105/feature_calmini_rocksliders.htm
     
Logged
*

Offline WAGON08

  • 78
  • 1
  • Gender: Male
Re: Removing the rocker trim support.
« Reply #2 on: July 25, 2012, 12:06:22 PM »
  When i did mine i removed the plastic panels then i just took a flat head screwdriver and started slowly just working it behind the support.  Its tacked  every 6'' to 8''  when i would find a spot that was tack i would just break the weld with the screw driver and a hammer. A little tuff on the metal work but i was planning on redoing that anyway.
Logged
87 sami
30x10.5 maxis mudders
stock 1.3L
*

Offline Godzuki84

  • 67
  • 0
  • Gender: Male
Re: Removing the rocker trim support.
« Reply #3 on: July 25, 2012, 02:33:13 PM »
Quote from: WAGON08 on July 25, 2012, 12:06:22 PM
  When i did mine i removed the plastic panels then i just took a flat head screwdriver and started slowly just working it behind the support.  Its tacked  every 6'' to 8''  when i would find a spot that was tack i would just break the weld with the screw driver and a hammer. A little tuff on the metal work but i was planning on redoing that anyway.

I removed mine the same way.
Logged
The little zuki that could
*

Offline tuxblacray

  • 930
  • 20
  • Gender: Male
  • Building a Bigger Better Brute Samurai.... B-}
    • Tuxblacray Photos
Re: Removing the rocker trim support.
« Reply #4 on: July 28, 2012, 02:53:09 AM »

If you have access to a die grinder with a cutting wheel or a spot weld remover drill bit these both do a nice clean job with a minimal amount of body work to remain.
Logged
I know the voices aren't real.... but they have some pretty kewl ideas!!! Tux.....  ;-)
I get my Sammi parts here, and you can too... http://www.mikodaindustries.com/http://stores.ebay.com/sticksnstones4x4samuraiparts
*

Offline dustedwatts

  • 12
  • 0
Re: Removing the rocker trim support.
« Reply #5 on: August 08, 2012, 03:51:29 PM »
Quote from: pharoe7 on July 23, 2012, 05:45:56 PM
Does anyone know the best way to remove the metal support for the plastic molding on the rocker panel below the doors? I've taken the plastic molding off already but the metal support seems to be on there pretty good either glued or welded, I can't tell. Though I don't see any welds. Let me know if anyone has removed it successfully.

Thanks
what did you do w/ the plastic pieces?
Logged
*

Offline my996duc1

  • 222
  • 7
Re: Removing the rocker trim support.
« Reply #6 on: August 11, 2012, 12:13:33 AM »
The spot welds are there and you have too look really close to see them.

I used a spot weld cutter. Just chuck it up in your drill and you are set. Super simple to use.
Cheap = $5
Worked great and is made exactly for this type of stuff.

http://www.harborfreight.com/3-8-eighth-inch-double-sided-rotary-spot-weld-cutter-95343.html

_
« Last Edit: August 11, 2012, 12:15:14 AM by my996duc1 »
Logged
1987 Tintop / 1.6 16V ps & ac / 6.4 t-case Twisted TT / 4.30 R&P Hybrid rear / Double Tough axles / Shrockworks all around / ARB f&r / Mighty Kong & TT full skid / DS disconnect / CV shafts f & r / YJ missing links f & r / Petroworks tintop cage / 15 gal Tank / 31" x 12.50 Pro Comps
Pages: [1]   Go Up
« previous next »