Hello Guest
« previous next »
Pages: [1]   Go Down

Hood clearace

  • 7 Replies
  • 2055 Views

0 Members and 1 Guest are viewing this topic.

*

Offline dupont#24

  • 48
  • 2
  • Gender: Male
  • Deer hunter
Hood clearace
« on: November 19, 2009, 07:22:06 PM »
I just put 89 geo motor in my 87 sammy and I have major hood clearance problem with that bigger horn on the 89 injector.I don't think just cutting out the x brace under the hood is going to do it.I really don't want a body lift but it is looking like I have no choice .It looks like it will take at lest a 2 inch what do you guys do about this problem . will a 1 inch body work 
Logged
*

Offline mrfuelish

  • *
  • 2862
  • 13
  • Gender: Male
  • you must have a perception problem.
Re: Hood clearace
« Reply #1 on: November 19, 2009, 10:49:07 PM »
man I would cut the motor mounts and lower the engine before the body lift, you can even cut the frame mounts off and lower them and weld them back on and then lower the trans mount to match.
Logged
1987,1988,1988,1990 samurai's,  1953 m38a1,  1996 x-90,blue.1996 x-90 red.1994 2 door tracker.   only Dead Fish go with the flow.                No Hairy Nosed Wombats were ran over on the trail today.       My ZUK is Xenophobic.
*

Offline Bobzooki

  • 1754
  • 2
  • Gender: Male
  • Web Wheeler
Re: Hood clearace
« Reply #2 on: November 20, 2009, 07:13:20 AM »
Hood Scoop?
Logged
Bob

Tahoe 24' Fish-N-Fun Tritoon
115 HP Mercury outboard
*

Offline Cuthulu

  • 384
  • 0
  • Gender: Male
  • I'd kill for a Nobel Peace Prize.
Re: Hood clearace
« Reply #3 on: November 20, 2009, 09:16:21 AM »
Quote from: mrfuelish on November 19, 2009, 10:49:07 PM
man I would cut the motor mounts and lower the engine before the body lift, you can even cut the frame mounts off and lower them and weld them back on and then lower the trans mount to match.

One advatage to this is that if you did a suspension lift it would take off some extra tension in the CV joints.
Logged
*

Offline Rhinoman

  • 4502
  • 36
  • Gender: Male
  • Bend it, Break it, Fix it
    • Rhinoman
Re: Hood clearace
« Reply #4 on: November 20, 2009, 11:08:17 AM »
I would go for the hood scoop. If you don't have a suspension lift then lowering the motor may give you clearance problems with the oil pan. Lifting the body will make it less stable and its only too low in one small area.
Logged
2000 Vitara 1.6, 3+3 Lift, 33"MTs, 5:83s, LWB brakes, Winch, Snorkel, Safari Rack
1986 SJ413K PickUp, 1.6L conversion.

OBD1 - Full diagnostics on a PC/Laptop: http://www.rhinopower.org
*

Offline dupont#24

  • 48
  • 2
  • Gender: Male
  • Deer hunter
Re: Hood clearace
« Reply #5 on: November 20, 2009, 03:47:19 PM »
where do yall get this hood scoops any pics I have plenty of lift 3inch rear spings on front and yj on rear.and still like 2inces shooting hood
« Last Edit: November 20, 2009, 03:50:53 PM by dupont#24 »
Logged
*

Offline ebewley

  • 6566
  • 66
  • Gender: Male
  • ZUKIWORLD Online, Editor
    • ZUKIWORLD online
Re: Hood clearace
« Reply #6 on: November 20, 2009, 03:48:28 PM »
Here's one from our Gallery section..



-Eric
Logged
Eric L. Bewley                               
Editor, ZUKIWORLD Online                   

Suzuki 4x4 Owners Association - Please Join  The ZUKIWORLD ORDER Today!
About ZUKIWORLD Online: We are an enthusiast web site dedicated to the promotion of the Suzuki Automobile as the best and most capable vehicle on the planet. We offer product reviews, Tech tips, DIY, Travel and Adventure, Forum, Technical information, Life Style, and so much more!
*

Offline dupont#24

  • 48
  • 2
  • Gender: Male
  • Deer hunter
Re: Hood clearace
« Reply #7 on: November 20, 2009, 03:52:28 PM »
will this fit a sammy
Logged
Pages: [1]   Go Up
« previous next »