Hello Guest
« previous next »
Pages: [1]   Go Down

CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)

  • 11 Replies
  • 2110 Views

0 Members and 1 Guest are viewing this topic.

*

from_wales

CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« on: June 16, 2007, 07:17:19 AM »
HI CAN ANY ONE ADVISE ME HOW TO CHANGE THIS CV JOINT GAITER. ON A VITARA.
I HAVE REMOVED THE DRIVE SHAFT.
THANKS
JEREMY
« Last Edit: June 16, 2007, 08:56:58 AM by from_wales »
Logged
*

Offline Rhinoman

  • 4502
  • 36
  • Gender: Male
  • Bend it, Break it, Fix it
    • Rhinoman
Re: CANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #1 on: June 16, 2007, 07:56:54 AM »
Pull the gaiter back. Underneath all the grease there is a circlip the needs to be removed to allow the CV joint to be seperated.
Logged
2000 Vitara 1.6, 3+3 Lift, 33"MTs, 5:83s, LWB brakes, Winch, Snorkel, Safari Rack
1986 SJ413K PickUp, 1.6L conversion.

OBD1 - Full diagnostics on a PC/Laptop: http://www.rhinopower.org
*

from_wales

Re: CANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #2 on: June 16, 2007, 07:59:29 AM »
IS THAT AT THE END THAT GOES TO THE WHEEL, OR THE END THAT GOES TO THE AXEL?
THANKS
JEREMY
Logged
*

Offline Rhinoman

  • 4502
  • 36
  • Gender: Male
  • Bend it, Break it, Fix it
    • Rhinoman
Re: CANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #3 on: June 16, 2007, 08:15:06 AM »
Its been a while since I did one. I'm pretty sure theres one at both ends.
Logged
2000 Vitara 1.6, 3+3 Lift, 33"MTs, 5:83s, LWB brakes, Winch, Snorkel, Safari Rack
1986 SJ413K PickUp, 1.6L conversion.

OBD1 - Full diagnostics on a PC/Laptop: http://www.rhinopower.org
*

from_wales

Re: CANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #4 on: June 16, 2007, 08:16:40 AM »
THANKS
JEREMY
Logged
*

from_wales

Re: CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #5 on: June 16, 2007, 08:35:10 AM »
CANT FIND NO CIRCLIP.
THERE'S A BEARING WITH 6 BALLS, WITH A STAR SHAPED DRIVE SHAFT IN IT.
ANY IDEAS?
THANKS
JEREMY
« Last Edit: June 16, 2007, 08:57:49 AM by from_wales »
Logged
*

Offline crikeymike

  • 713
  • 0
  • Gender: Male
  • Local to Western Washington?? Visit WAZUKS.com
    • http://www.wazuks.com
Re: CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #6 on: June 16, 2007, 10:17:04 AM »
I'm trying to remember too, but i'm pretty sure you have to remove the cv and boot from the wheel end, then slide the boot from the diff end down and off the other end.  Only one end of the CV will have the 1" diameter hole to pull the boots off correctly.  There is a circlip in there somewhere, but i can't remember where exactly.

Anyway, remember you have to start from the wheel end and work your way backwards into it.
Logged
1993 4-door Sidekick
3" hybrid Calmini/OME lift, 2" B/L, Rear air locker
Shrockworks bar & sliders, Full skid plates
4.24:1 t-case
 WAZUKS member - visit http://www.wazuks.com
*

Offline ack

  • 1659
  • 34
  • Gender: Male
  • Professional askhole
    • Ack's FAQ
Re: CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #7 on: June 16, 2007, 01:13:36 PM »
I thought that I had replied to this...


Try this article:

http://www.acksfaq.com/cvhalfshaft.html


Hope this helps!
Logged
Ack

'88 Samurai, '88.5 Samurai TT, '11 Ford Transit Connect XLT
Ack's FAQ  http://www.acksfaq.com
*

from_wales

Re: CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #8 on: June 16, 2007, 02:55:07 PM »
THANKS FOR YOUR HELP
JEREMY
Logged
*

from_wales

Re: CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #9 on: June 17, 2007, 02:51:13 AM »
ALL DONE NOW, THANKS FOR ALL YOUR HELP.
FOR REFERENCE: THE CIRCLIP IS ON THE END CLOSEST TO THE AXEL.
THANKS AGAIN
JEREMY
Logged
*

Offline crikeymike

  • 713
  • 0
  • Gender: Male
  • Local to Western Washington?? Visit WAZUKS.com
    • http://www.wazuks.com
Re: CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #10 on: June 17, 2007, 09:55:26 AM »
Quote from: from_wales on June 17, 2007, 02:51:13 AM
ALL DONE NOW, THANKS FOR ALL YOUR HELP.
FOR REFERENCE: THE CIRCLIP IS ON THE END CLOSEST TO THE AXEL.
THANKS AGAIN
JEREMY


Technically, you're working on an axle.  Do you mean closer to the diff end?
Logged
1993 4-door Sidekick
3" hybrid Calmini/OME lift, 2" B/L, Rear air locker
Shrockworks bar & sliders, Full skid plates
4.24:1 t-case
 WAZUKS member - visit http://www.wazuks.com
*

from_wales

Re: CHANGING THE FRONT CONSTANT VELOCITY JOINT GAITER (CV JOINT)
« Reply #11 on: June 17, 2007, 10:09:48 AM »
YES I DO.
THANKS
JEREMY
Logged
Pages: [1]   Go Up
« previous next »