Hello Guest
« previous next »
Pages: [1]   Go Down

Starter Not Engaging

  • 11 Replies
  • 4062 Views

0 Members and 1 Guest are viewing this topic.

*

Offline 87Sam87

  • 63
  • 0
  • Gender: Male
  • '87 Samurai JA and '86 Samurai JX
Starter Not Engaging
« on: May 05, 2008, 08:35:36 AM »
  When I try to start my Samurai the starter winds up and I can hear it spinning but it doesn't engage with the engine. Should I just replace the starter?

Thanks
Logged
*

Offline rascott

  • 669
  • 15
  • Gender: Male
  • tread lightly monkeywrench a little
Re: Starter Not Engaging
« Reply #1 on: May 05, 2008, 10:04:34 AM »
sounds like the drive gear mechanism is screwed up.
i don't mess with them anymore and get a rebuilt from kragen auto parts(cause that's local + lifetime warranty).
i do that with alternators also, and have had pretty good service outa them.
i suspect you have a local parts place that does the same?
Logged
'89 kick w/little motor, still got pieces of jeff's pucks, stan's sticks into 4.24:1 tcase, 31x10.5x15's, rear lockrite, kick power steering, some radios(kj6esv), bmw seat, other changes just because. done on the cheap.
suzi the psychic gets me fishing.
*

Offline 87Sam87

  • 63
  • 0
  • Gender: Male
  • '87 Samurai JA and '86 Samurai JX
Re: Starter Not Engaging
« Reply #2 on: May 05, 2008, 03:19:42 PM »
   Yes I can get a lifetime exchange warranty from the local part store. I did test the solenoid and it's working so I think it's either the starter gear or the slip clutch.
   
   Does anybody have any tricks for getting the starter out of the Samurai? It's looking like that bolt on the top is going to be tough to get out.
Logged
*

Offline rascott

  • 669
  • 15
  • Gender: Male
  • tread lightly monkeywrench a little
Re: Starter Not Engaging
« Reply #3 on: May 05, 2008, 03:42:41 PM »
probably like my 1.3 kick-
the top bolt has a nut in back?
it was fun wiggling it out after unbolting. same with install.
Logged
'89 kick w/little motor, still got pieces of jeff's pucks, stan's sticks into 4.24:1 tcase, 31x10.5x15's, rear lockrite, kick power steering, some radios(kj6esv), bmw seat, other changes just because. done on the cheap.
suzi the psychic gets me fishing.
*

Offline Amilla

  • 1076
  • 0
  • Gender: Male
  • Toyota running gear was made for a samurai!
Re: Starter Not Engaging
« Reply #4 on: May 05, 2008, 05:46:29 PM »
I just pulled my starter out a week ago, and then just threw it back in.
That top bolt with a nut isn't to bad to get to but you defiantly have to wiggle your arm in there.  The bottom one is a piece of cake.

Don't forget the bracket that goes between the starter and the bell housing when your putting it back in. 

Amilla
Logged
88 Samurai, Sprung Up, Geared Down, Locked,With Yotas.
*

Offline rascott

  • 669
  • 15
  • Gender: Male
  • tread lightly monkeywrench a little
Re: Starter Not Engaging
« Reply #5 on: May 05, 2008, 07:08:17 PM »
is my kick supposed to have a bracket also?
(sorry to piggyback, but i just wondered)
Logged
'89 kick w/little motor, still got pieces of jeff's pucks, stan's sticks into 4.24:1 tcase, 31x10.5x15's, rear lockrite, kick power steering, some radios(kj6esv), bmw seat, other changes just because. done on the cheap.
suzi the psychic gets me fishing.
*

Offline lostsamurai

  • 433
  • 0
  • Gender: Male
  • LOSTSAMURAI
Re: Starter Not Engaging
« Reply #6 on: May 05, 2008, 08:04:43 PM »
roll it then pop it in gear just to turn the flywheel a bit could be missing a tooth right where its sitting, also check the starter bolts mine used to come loose alot and grind teeth
Logged
88' Zuk 16v efi full width dana 44 axles and 37"s,hybrid exo cage, comp cut rear -18", F&R fox air shocks , jegs poly seats, sk automatic trans, 6.5:1 t case, twinsticks, 100" wheelbase with a 79" wide.
*

Offline Amilla

  • 1076
  • 0
  • Gender: Male
  • Toyota running gear was made for a samurai!
Re: Starter Not Engaging
« Reply #7 on: May 05, 2008, 10:34:11 PM »
Im not sure if kicks have the bracket too but on a sami, theres bracket that goes in there that holds 2 lines in place. 
Mine was out when i pulled the starter, who ever did it before forgot to put i back in.
There were never any starter issues  caused by it not being there.

Amilla
Logged
88 Samurai, Sprung Up, Geared Down, Locked,With Yotas.
*

Offline 87Sam87

  • 63
  • 0
  • Gender: Male
  • '87 Samurai JA and '86 Samurai JX
Re: Starter Not Engaging
« Reply #8 on: May 06, 2008, 10:14:17 AM »
   I've pop started it a couple times and the problem keeps coming back so I guess I'm going to have to pull the starter.
   So you guys that have pulled the starter out, did you remove the heater hose above that top bolt? Did you just use a socket wrench on the bolt or what?

Thanks for all the help by the way, you guys are great!
Logged
*

Offline Amilla

  • 1076
  • 0
  • Gender: Male
  • Toyota running gear was made for a samurai!
Re: Starter Not Engaging
« Reply #9 on: May 06, 2008, 02:10:30 PM »
I didn't pull any lines off, just worked my arms in around them.

Gear wrenches make life sooo much easier!

Amilla
Logged
88 Samurai, Sprung Up, Geared Down, Locked,With Yotas.
*

Offline kingzoo

  • 461
  • 0
  • Gender: Male
  • I LOVE MY JLX SIDEKICK
Re: Starter Not Engaging
« Reply #10 on: May 06, 2008, 04:23:19 PM »
   DITTO for gear wrenches!
Logged
KING ZOO!!
*

Offline 87Sam87

  • 63
  • 0
  • Gender: Male
  • '87 Samurai JA and '86 Samurai JX
Re: Starter Not Engaging
« Reply #11 on: May 06, 2008, 09:49:50 PM »
   Gear wrenches, great idea!  I'd seen them but never bought any. I'll pick some up and give it a try.
Logged
Pages: [1]   Go Up
« previous next »